Blog

Read our latest technical newsletter, MIM tips for designers & press releases.

What's new

The story of powder evaluation - Part 2

The story of powder evaluation - Part 2

In the previous report, we discussed the evaluation of metal powders. In the powder metallurgy industry, the process of kneading (mixing main raw material with sub materials) is unavoidable. This time, we will move on to the kneading stage.
Read more
The story of powder evaluation - Part 1

The story of powder evaluation - Part 1

It's been a while since the "I want to know but can't ask” series. We will discuss the basics, realities, and concerns of powder, which serve as the starting point for manufacturing, not only in the MIM industry but also in various other industries, over several issues.
Read more
Check out our technology article in the "INNO" magazine from IVAM Microtechnology Network!
Press releases
November 20, 2023

Check out our technology article in the "INNO" magazine from IVAM Microtechnology Network!

You can check out our technology article in the "INNO" magazine from IVAM Microtechnology Network now! Please take a look to learn more about our technology.What is INNO?
Read more

All posts by category

Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.
Tips #05
Announcement: Exhibiting at MD&M West 2024
Press releases
October 27, 2023

Announcement: Exhibiting at MD&M West 2024

We will be exhibiting at MD&M West 2024 to be held at the Anaheim Convention Center, Anaheim, California, USA from February 6 to 8, 2024.
Read more
Tips #05
Comparisons and characteristics of compaction, MIM and HIP in terms of density

Comparisons and characteristics of compaction, MIM and HIP in terms of density

Metal components manufactured by powder metallurgy tend to be regarded as having a low density compared to machined or stamped wrought material. Although, low density can be an advantage depending on the applications, but in general operations, high density is required to meet the mechanical strength requirements assumed in the design phase. In this issue, we introduce the characteristics of powder metallurgy from the perspective of density.
Read more
Tips #05
β-Titanium alloys by MIM manufacturing

β-Titanium alloys by MIM manufacturing

β-Ti (Beta Titanium) alloys have received a lot of attention as the next generation implant material in medical industry. In this issue, we introduce the reasons of β-Ti alloys attract attentions and our progresses of MIM process development.‍
Read more
Tips #05
Our latest interview with Easy Engineering Magazine was published
Press releases
June 15, 2023

Our latest interview with Easy Engineering Magazine was published

Please check out our latest interview with Easy Engineering Magazine about our business and technologies!
Read more
Tips #05
μ-MIM® realises quality micro gears!

μ-MIM® realises quality micro gears!

In the previous issue, we explained that gears with diameters of a few millimetres, small modules in special shapes such as bevel and bevel teeth (bevel, miter, helical and etc.) are difficult to machine, and are typical of high cost gears.
Read more
Tips #05
 Diameter less than 1 mm, module of < 0.3 mm!

Diameter less than 1 mm, module of < 0.3 mm!

We have continued to research and develop special-shaped micro gears manufacturing by μ-MIM® technology.
Read more

Read our micro MIM technical Newsletter

Our technical newsletter is about our μ-MIM® technology including the latest development of Micro MIM Japan.
Read our latest micro MIM technical newsletter and subscribe to our email list.

Read our MIM tips for designers

Our technical newsletter is about our μ-MIM® technology including the latest development of Micro MIM Japan.

See our latest news and press releases

Our technical newsletter is about our μ-MIM® technology including the latest development of Micro MIM Japan.
Read our latest press releases and subscribe to our newsletter.

Sign up for our next free webinar

Learn more about μ-MIM® technology in one of our upcoming webinars.